Serving NYC & NJ Since 1924| Licensed, Bonded & Insured| FDNY Compliant| Fast Turnaround • 3–5 Days
(718) 455-8442  — 24/7 Emergency
Universal Fireproof Door

NYC’s Most Trusted Fire Door Contractor

✓ Manufacturer & Installer|✓ Est. 1924|✓ All 5 NYC Boroughs

5% Off — New Clients Only

In-house manufacturing & installation.
No subcontractors. Best price guaranteed.

(718) 455-8442

MON–FRI  7AM–5PM

★★★★★ 5.0 Google · Manufacturer & installer since 1924

U.S. Architects: Show the 32in Minimum on Double Egress Plans

MEA ApprovedUL ListedFDNY CompliantNFPA 80NYC DOBLicensed & Insured
Free Estimates — We Respond in 2 Hours

Get Your Free Same-Day Estimate

Tell us about your building — we manufacture & install in 3–5 days. No middlemen. No delays.

✓No obligation|✓Licensed & Insured|✓FDNY Compliant|✓2-Hour Response|📞 (718) 455-8442

Double egress doors must meet a 32 inch minimum clear opening (41.5 inches for I-2 bed movement), swing in the direction of exit travel once occupant load hits 50 people or the space is high hazard, and open from the inside without keys or tools. For paired leaves without a mullion, only one leaf has to deliver that required clear opening, unless both sides independently need it. Confirm which leaf carries that load before hardware gets ordered.


TL;DR:

  • Only one leaf in a pair without a mullion must meet the 32-inch minimum clear opening, unless occupant load on both sides independently requires it.
  • The door latch must operate from the inside without keys, tools, or special knowledge, with panic hardware often mandatory for high-occupant or assembly spaces.
  • When occupant load exceeds 50 or the space is high hazard, the door on that side must swing in the direction of egress, and the required clear opening applies to that specific leaf.
  • Threshold height is generally limited to 0.5 inches, and force limits for unlatching are typically 5 pounds for non-fire-rated doors and up to 30 pounds for fire-rated ones.
  • Conduct on-site verification of measurements, hardware operation, labeling, and thresholds after installation, documenting any discrepancies to ensure compliance.

Universal Fireproof Door
Specify Fire Rated Doors With Confidence
Universal Fireproof Door supplies, installs, repairs, and maintains fire rated steel doors, frames, and commercial hardware.

Visit Universal Fireproof Door

Table of Contents

Double Egress Door Requirements: The Field Checklist

Plan reviewers and inspectors work off the same short list, whether they are checking a hospital corridor or a warehouse exit. Run through these before a drawing set goes out for permit, and again before final inspection.

  1. Clear opening width. Measure with the door open to 90 degrees, from the face of the door to the stop. The result must hit 32 inches, or 41.5 inches for I-2 occupancies where the door handles bed movement, per OSHA’s exit route standard.
  2. Clear opening height. 80 inches minimum, measured the same way as width.
  3. Swing direction. Confirm and document which side has the higher occupant load, and whether that load crosses the 50-person threshold that triggers outswing under IBC Chapter 10.
  4. Hardware operation. Verify the door opens from the inside without a key, a tool, or specialized knowledge of any kind.
  5. Prohibited devices. Flag any alarm, delay, or locking mechanism that could trap occupants if it fails, per 29 CFR 1910.37.
  6. Thresholds and force limits. Check maximum threshold height and confirm opening and unlatching forces fall within code limits for the door type.
  7. Landing depth. Confirm the landing on each side of the door meets minimum depth, with no obstruction into the swing path.
  8. Fire label verification. For any fire-rated leaf, confirm the label is legible and matches the listed assembly on the door schedule.

Pro Tip: Keep a physical copy of the door schedule on site during rough-in. Field crews swap hardware more often than designers expect, and an unlabeled substitution at week six of installation is far harder to catch than a labeling mismatch caught at delivery.

How Codes Treat One Leaf vs. Two Leaves in a Pair

The rule that trips up more plan reviewers than any other: a pair of doors without a center mullion does not need both leaves to hit 32 inches. One leaf has to provide the required clear opening. The other can be narrower and is often used only when both doors are opened together for equipment or gurney movement.

Gurney moving through paired egress opening

Opposite-swing pairs complicate that math. When occupant load requires a leaf to swing in the direction of egress, that specific leaf must independently meet the required clear opening, according to guidance from iDigHardware’s code Q&A column. It is not enough for the pair combined to add up to 32 inches if the egress-side leaf alone falls short.

Typical scenarios where this matters:

  • A stairwell pair where only one side sees regular occupant travel: the travel-side leaf carries the requirement.
  • A double-egress corridor pair in a hospital where both directions see meaningful occupant load: both leaves may need to independently qualify.
  • A storage room pair with one leaf used only for oversized equipment: the equipment leaf may be undersized as long as the egress leaf meets the minimum.

Picture the pair as two independent doors sharing a frame, not one 64-inch opening split down the middle.

What Hardware Belongs on a Double Egress Pair

Every double egress door has to satisfy one non-negotiable rule: it opens from the inside without a key, a tool, or any special knowledge, a requirement OSHA spells out directly in its exit route design standard. Panic hardware is permitted, and often required, on doors serving higher occupant loads or assembly spaces.

Where designers get into trouble is electrified security hardware. Electromagnetic shear locks show up often on opposite-swing pairs because they seem like a clean way to secure a corridor. In practice, they create more problems than they solve: alignment drifts over time on paired leaves, fail-safe wiring has to interface correctly with the fire alarm system, and a maintenance lapse can leave a door either unsecured or, worse, unable to release during an alarm condition. Industry guidance on double egress pairs flags this as one of the most common life-safety conflicts on paired doors.

Specify instead:

  • Listed panic hardware or fire exit hardware rated for the assembly.
  • Electrified hardware only when it has a documented fail-safe interface with the building’s fire alarm and power-fail sequence.
  • A maintenance schedule the AHJ can review, especially for any electrified component.

For a deeper look at fail-safe interfacing, Modern Fence Company’s access control guidance covers the trade-offs between security and egress reliability in more detail.

Pro Tip: If a security consultant proposes a shear lock on an opposite-swing pair, ask for the fail-safe test documentation before it goes on the schedule. If nobody can produce it, that is the answer.

Dimensions, Force Limits, and Thresholds to Put on the Schedule

Every door schedule entry for a double egress pair needs a specific set of numbers, not a generic note that says “verify code compliance in field.”

  • Clear opening width: 32 inches minimum, measured door-open-90-degrees, face to stop.
  • Bed movement width: 41.5 inches for I-2 occupancies where the door serves patient bed or gurney transfer paths, such as hospital corridors and ambulance transfer routes.
  • Clear opening height: 80 inches minimum.
  • Threshold height: Typically capped at 0.5 inches for accessible routes.
  • Landing depth: Generally 44 inches minimum on each side, with narrower exceptions for certain residential conditions.
  • Opening and unlatching force: Manual interior swinging doors that are not fire-rated generally cannot exceed 5 pounds-force to unlatch; fire-rated and exterior doors fall into higher force categories, up to 15 to 30 pounds depending on the specific IBC provision governing that door type.

That 41.5 inch figure is the one number that catches design teams off guard most often. A hospital corridor sized to the standard 32 inch minimum will fail an equipment transfer test the day a gurney with side rails needs to pass through. Get the occupancy classification and the intended use confirmed before the opening width goes final. Record the measurement method directly on the schedule: “clear opening, 90 degrees” and note which leaf, left or right, carries the required width.

Working Out Which Leaf Swings and Why

Occupant load drives every swing decision on a double egress pair, and getting the math wrong on paper is the single fastest way to fail a plan review.

  1. Calculate the occupant load for each side of the door independently, using the applicable occupant load factor for that space’s use.
  2. Compare the higher of the two loads against the 50-person threshold. If it meets or exceeds 50, or the space is high hazard, that side’s leaf must swing in the direction of egress.
  3. Assign the required clear opening width to the leaf carrying that occupant load, not automatically to whichever leaf is labeled “active” on the hardware schedule.
  4. Document the occupant load calculation directly on the plan sheet, with a callout identifying the egress leaf and a reference to the governing IBC section.

A frequent mistake: teams size the leaf that is easiest to access from the corridor, rather than the one serving the higher occupant load. For a fuller walkthrough of the 50-person threshold, see this breakdown of egress door swing direction rules.

Smoke-Stop Pairs and the Healthcare Bed Movement Exception

Not every double egress pair needs to be fire-rated. In many I-2 healthcare corridors, paired doors function as smoke-stop assemblies, controlling smoke migration during a fire event without carrying a fire-resistance rating. Specifying a fire-rated assembly where a smoke-stop pair would satisfy code adds cost with no life-safety benefit, a mistake iDigHardware’s healthcare-specific guidance flags as common.

Key points for healthcare projects:

  • Confirm with the AHJ early whether the corridor requires a fire-rated assembly or a smoke-stop pair, since the two carry different hardware and closer requirements.
  • Where bed or gurney movement is part of the intended use, size the clear opening to 41.5 inches and document that rationale on the drawings.
  • Loop in facility operations staff before finalizing hardware. Equipment sizes and transport patterns often change between design and occupancy.

Verifying Compliance on Site After Installation

Code language only matters once it gets built correctly. Field verification should cover the same items as the plan review, plus a few that only show up once the door is hung: hardware operation under repeated use, alignment on opposite-swing pairs, and whether the threshold height has crept up during flooring installation.

  • Confirm clear opening and height with the door at 90 degrees, matching the schedule.
  • Test hardware operation from the inside without keys or tools, on both leaves.
  • Check labels on fire-rated components against the listed assembly.
  • Inspect thresholds, landings, and signage for obstruction or drift since installation.
  • Log any corrective action taken, with photos, for AHJ re-inspection records.

Some companies handle this kind of verification directly, managing the manufacturing, installation, and inspection of fire-rated steel doors and hardware for buildings in urban and regional areas. Field teams see the same misalignment and mislabeling issues repeatedly across multi-building portfolios, which is part of why documentation at each stage matters as much as the installation itself.

Pro Tip: Photograph the door schedule label next to the installed hardware at final walkthrough. It takes thirty seconds and settles most compliance disputes before they start.

Where Double Egress Compliance Actually Breaks Down

Most double egress problems trace back to three habits: measuring clear opening with the door at the wrong angle, skipping the occupant load documentation entirely, and swapping hardware late in construction without checking it against the original schedule. None of these are complicated fixes. They just require someone to check the math before the door gets hung, not after.

Get the design team, the specification writer, and the installer talking early, and keep hardware choices inside what the code actually permits rather than what a security vendor is selling that quarter.

— Esteban

Getting Your Double Egress Doors Right the First Time

Getting a double egress pair through plan review and past final inspection on the first try means having someone who manufactures the door, installs it, and understands the code checking every measurement. A company that builds fire-rated steel doors and frames in-house and installs them without subcontractors can ensure the same team fabricates and hangs the door, providing accountability behind the sign-off.

Universal Fireproof Door

That matters most on opposite-swing pairs, where a mismeasured leaf or the wrong hardware interface can fail an inspection months after installation. Whether you need a custom door and frame manufactured to your schedule, a full installation and hardware setup, or a compliance inspection ahead of an AHJ visit, request a site estimate and get the dimensions confirmed before the order goes to fabrication.

Sources

For plan check and AHJ submissions, three sources cover nearly every double egress question:

FAQ

What Is the Minimum Clear Opening for a Double Egress Door?

32 inches for most occupancies, measured with the door open to 90 degrees from the face of the door to the stop. I-2 occupancies using the door for bed movement need 41.5 inches.

Does Each Leaf in a Pair Need to Meet the 32 Inch Minimum?

No. For pairs without a mullion, only one leaf has to provide the required clear opening, unless occupant load on both sides independently triggers the requirement on each leaf.

When Must an Egress Door Swing in the Direction of Travel?

When the occupant load served by that door reaches 50 people or more, or the space is classified high hazard, per OSHA’s exit route standard.

Can a Double Egress Pair Use an Electromagnetic Shear Lock?

It’s generally a poor choice on opposite-swing pairs because of alignment drift and fail-safe interface risk. Listed panic or fire exit hardware is the safer specification for most projects.

Does Universal Fireproof Door Handle Double Egress Door Inspections?

Yes. Universal Fireproof Door Co., Inc. manufactures, installs, and inspects fire-rated steel doors and hardware, including double egress pairs, for buildings throughout New York City and the Northeast.

Free Estimates · 2-Hour Response

Need fire door help in NYC?

We manufacture & install in 3–5 days. Violations, replacements & inspections across all 5 boroughs.

Get a Free Estimate →📞 (718) 455-8442Mon–Fri 8AM–4:30PM · No obligation

Why Universal Fireproof Door

  • ✓ Manufacturing in Brooklyn since 1924
  • ✓ UL Listed & NYC MEA Approved
  • ✓ Our own crews — no subcontractors
  • ✓ Serving all 5 NYC boroughs & Long Island

Related Articles

U.S. Architects: Show the 32in Minimum on Double Egress Plans

Leave a Reply

Your email address will not be published. Required fields are marked *

U.S. Architects: Show the 32in Minimum on Double Egress Plans

Leave a Reply

Your email address will not be published. Required fields are marked *