There is no single “FDNY-approved hardware” stamp that clears every closer, hinge and latch in New York City. Approval comes in layers: a third-party label on the door assembly, listed components, NYC acceptance records for certain assemblies, and an FDNY Certificate of Approval for certain products and systems. This guide explains how those layers fit together, what to ask for before you buy or install, and what to keep on file for an inspector.
It is written for property managers, facility managers, building owners and general contractors who sign for the work.
TL;DR
- Fire door assemblies must carry a permanent label from an approved third-party agency, showing the manufacturer, the agency and the fire protection rating.
- Hardware on a rated opening should be listed or classified for that use. Closers, hinges and latches that do not suit the rated assembly can cause a failed inspection even if the door slab is fine.
- The FDNY Certificate of Approval applies to specific products, systems or equipment named in the Fire Code. It is not a blanket approval for door hardware.
- Keep labels, shipment certificates and installation records together. They are your proof when a violation arrives.
- Self-closing door violations in multiple dwellings carry a 14-day repair window, so spares and a fast installer matter.
Table of Contents
- What “FDNY approval” of door hardware actually means
- Which hardware on a fire door is under scrutiny
- MEA acceptance: the record behind many assemblies
- How to verify hardware before it goes on the door
- Documents to keep on file
- Installation: where approved hardware goes wrong
- Self-closing doors and the 14-day clock
- Our perspective: approval is a chain, and one weak link fails the opening
- When to bring in a manufacturer-installer
- What happens when hardware does not comply
- FAQ
- Sources
What “FDNY approval” of door hardware actually means
When people search for FDNY door hardware approval, they usually mean one of three different things.
- A labeled, rated assembly. Under the NYC Administrative Code, fire doors must be labeled by an approved third-party inspection agency, with the label permanently affixed at the factory. It shows the manufacturer, the inspection agency and the fire protection rating.
- Listed components. Hardware may be listed or classified and labeled for that use, sometimes by a different agency than the one that labeled the door. The same code section says listed vision light kits and louvers, with their required preparations, count as part of the labeled door when they are listed and covered by the agency’s quality assurance testing.
- An FDNY Certificate of Approval (COA). The FDNY requires a COA for certain products, systems or equipment specified in Fire Code Section FC 112. It confirms review and approval for a specific use. It is a product-specific tool, not a catch-all for every door part.
The practical consequence: asking a supplier “is this FDNY approved?” is the wrong question. Ask instead: what is the label on the door and frame, is each hardware item listed for use on a rated opening, and does any product in the opening need NYC acceptance or a COA?
Which hardware on a fire door is under scrutiny
Inspectors look at the whole opening, not only the door leaf. The parts that most often draw attention:
- Closers. Fire doors protecting openings must be self-closing or automatic-closing. Per FC Chapter 7, swinging fire doors must close from the full-open position and latch automatically, and the closer needs enough force to close and latch from any partially open position.
- Latching hardware. A door that closes but does not latch is a failure. Mortise locks and latch sets must be the listed type for the assembly.
- Hinges. NYC’s own acceptance record for a fire-rated hollow metal door and frame assembly specifies a listed and labeled mortise lock and listed hinges. Loose, missing or defective hinges are also a named concern in HPD guidance on self-closing doors.
- Automatic closing mechanisms. Per the Administrative Code, fusible links and similar mechanisms must be NYC-approved.
- Egress hardware. Door hardware and other physical components of the means of egress must be maintained in good working order at all times. Security devices that affect egress are subject to approval by the Commissioner of Buildings in consultation with the Fire Commissioner. This is where access control, electrified locks and delayed-egress devices get extra attention.
For a deeper look at panic devices and latching, see our guide to fire door hardware requirements in NYC.
MEA acceptance: the record behind many assemblies
The Department of Buildings issues Materials and Equipment Acceptance (MEA) records. They describe an assembly, the testing behind it and the conditions of use. A published example covers a fire-rated hollow metal door and frame assembly accepted on the strength of Intertek testing to RS 5-6 (ASTM E152) and UL 10C. The acceptance record is dated 2007, and it shows what these documents typically contain: the tested configuration, the hardware that goes with it, the installation standard and the paperwork that must travel with the shipment.
Two takeaways for owners:
- The record ties acceptance to a specific assembly. Swapping in hardware that was not part of the tested or listed configuration can take the opening outside what was accepted.
- Acceptance is not permanent in every circumstance. Materials that fail retesting may have their acceptance restricted or discontinued by the Buildings Commissioner when needed to secure safety. Check that the product you buy is still current, not just that it once had a record.
How to verify hardware before it goes on the door
A short checklist you can hand to a superintendent, a purchasing agent or a GC:
- Read the door and frame labels. Confirm the manufacturer, agency and rating are there and legible. Our guides on how to read a fire door label and how to tell if a door is fire rated walk through it.
- Ask for the hardware schedule with listings. Every closer, hinge, lockset, exit device and flush bolt should be shown as listed for fire door use.
- Check the shipment paperwork. Shipments of accepted assemblies must include testing-service certificates or labels and a metal tag certifying that the materials are equivalent to those tested and accepted. The certificates must come from a testing service regularly engaged by the manufacturer to make periodic inspections or tests during manufacture.
- Confirm the clearances and the installation standard. Fire-rated assemblies must be installed according to testing laboratory limitations, manufacturer instructions and Reference Standard RS 5-8 (NFPA 80) for the class of opening. See our note on fire door clearance requirements.
- Flag anything that touches alarms or access control. Electrified hardware, magnetic holders and delayed egress usually involve more than one agency. Plan for coordination early.
Documents to keep on file
| Document | What it proves | Where it comes from |
|---|---|---|
| Door and frame labels (photos of each opening) | Rated assembly, manufacturer, agency | Factory-applied, on the door and frame |
| Hardware schedule with listing information | Each component suits a rated opening | Supplier or installer |
| Shipment certificates and metal tag | Delivered material matches what was tested and accepted | Manufacturer’s testing service |
| Installation record | Work followed manufacturer instructions and NFPA 80 | Installer |
| Annual inspection report | Operation and condition over time | Qualified inspector |
If your building is also tracking annual testing, our guides on NFPA 80 fire door inspection requirements in NYC and the fire door inspection checklist show what a good report contains.
Installation: where approved hardware goes wrong
Approved parts can still fail if they are fitted badly. The common field problems we hear about from owners are closers that are adjusted too weak to latch, latches that miss the strike, doors that have been field-cut or drilled beyond what the label allows, and gaps that grew over time.
Other trades matter too. Cable, conduit and sleeve penetrations near rated openings and walls have their own rules, and a sloppy pull can undo the work. If your project includes low-voltage work around rated assemblies, review the NYC firestopping rules so the rework does not land on your punch list.
For general contractors working through scope and responsibility, our commercial fire door requirements guide for GCs covers who does what.

Self-closing doors and the 14-day clock
If you own a multiple dwelling, hardware condition is also an HPD matter. HPD’s January 2023 owner bulletin says self-closing door violations must be repaired within 14 days of the notice. It tells owners to make sure there are no defective closing mechanisms, no defective, missing or loose hinges and no excessive gaps.

The reasoning is simple, and HPD states it in its rule: self-closing doors help keep smoke from spreading into hallways and other apartments. The same rule says owners must keep these doors in good repair so they close and latch on their own, without manual assistance.
In practice that means a monthly walk of the stairs and corridors, a stock of the closers and hinges you use most, and an installer who can come back quickly. A 14-day window disappears fast when parts are on backorder.
Our perspective: approval is a chain, and one weak link fails the opening
We build the doors and frames ourselves in Brooklyn and install them with our own crews, so we see both ends of this problem. The most expensive mistakes we are called to fix rarely involve a bad door. They involve a good door with the wrong closer, a hinge swapped during a renovation, or paperwork nobody can find when the inspector asks.
Our advice to owners: stop asking whether a product is “approved” in the abstract. Ask who labeled it, what it is listed for, and whether the exact combination on your opening is one that was tested. If the answers are on paper, you are in good shape. If they are not, fix that before an inspection does it for you.
When one company fabricates, supplies hardware and installs, those answers stay in one place, and someone is accountable through sign-off.
— Esteban
When to bring in a manufacturer-installer
Call for help when you have a violation notice, when a rated opening is changing (new hardware, new access control, new frame), or when you cannot tell from the labels what you have. We supply and install fire-rated steel doors, hollow metal doors and frames and commercial hardware, and we handle violation removal and fire door repair across New York City and the Northeast. For a defined scope, request a site estimate and bring your violation notice or hardware schedule if you have one.
What happens when hardware does not comply
The immediate risk is a failed inspection and a violation with a cure period, like the 14-day HPD window above. The longer-term risk is to the product itself: acceptance of materials found not to comply on retesting can be restricted or discontinued, and the Commissioner may limit their use during retesting if needed for safety. If a product line you rely on changes status, you will need a compliant replacement for every opening that uses it.
The cheapest protection is documentation and routine checks. Our maintenance and testing guide sets out a simple cadence.
FAQ
Is there an FDNY-approved list of door hardware?
Not as a single list covering all hardware. The FDNY issues Certificates of Approval for specific products, systems or equipment named in Fire Code Section FC 112. For fire door hardware, the practical test is whether each part is listed or classified for use on a rated opening and consistent with the assembly’s label and any NYC acceptance record.
Do fire doors in NYC need to close automatically?
Yes. Fire doors protecting openings must be self-closing or automatic-closing. Swinging doors must close from the full-open position and latch, with enough closer force to do so from any partially open position.
What papers should come with a fire-rated door shipment?
Certificates or labels from the manufacturer’s testing service, plus a metal tag certifying that the material is equivalent to what was tested and accepted. The door and frame labels must also stay legible and in place after installation.
How fast must I fix a self-closing door violation?
For multiple dwellings, HPD’s January 2023 bulletin gives 14 days from the notice. Check the notice itself for your exact deadline, and contact the issuing agency if you need clarification.
Sources
- NYC Administrative Code, 716.5 Fire door and shutter assemblies
- FDNY, Certificates of Approval
- NYC DOB, Materials and Equipment Acceptance 42-07-M
- NYC DOB, Materials and Equipment Acceptance 304-07-M
- FDNY Fire Code, Chapter 7
- FDNY Fire Code, Chapter 10
- HPD, January 2023 Bulletin to Property Owners
- HPD, self-closing doors final rule
- NYC firestopping rules
